KingPlast ST75®
Ready to use silicate based finish coat for external and internal application.
Overview
KingPlast ST75 consists of silicate, mineral fillers, cellulose fibers, pigments, polymers, rehological additives and water. It is applied as a thin layer protective and decorative wall covering for internal and external application. It is a ready to use product that can be applied by trowel floating or spray to produce various types of textures and finishes.
Applications
- Wall coverings external and internal
- Decorative textured finishes
- As a component of the KingPlasst system (ETICS)
Advantages
- Hydrophobic
- Weather resistant for durable system
- Highly vapour permeable allowing concrete or substrates to breath
- Good thermal characteristics
- Variety of decorative textured finishes
- Variety of colors
- Nonflammable
- Easily cleaned
- COMPATIBILITY KingPlast ST75 complies with the requirements of ETAG 004
Technical Properties
| Property | Value | Standard |
|---|---|---|
| Appearance | Pasty liquid with different grain sizes | — |
| Density | 1.7 ± 0.15 depends on texture type | — |
| Bond with substrate | ≥ 0.35 MPa | EN1542 |
| pH | EN : 10 - 11 | ISO787-9 |
| Thermal conductivity | 0.7 ± 0.05 w/mk | EN1745 |
| Water absorption | 0.4 ± 0.05 kg/m².h0.5 (category W₂) | EN1062-3 |
| Water vapour transmition | ± 20 g/m².d (category | EN 130 |
| Durability against Freeze | Passes (Category W₂) | — |
| thaw | — | |
| VOC passing leed | ≤ 40 g/ltr | — |
| requirements | — | |
| FOR KINGPLAST PRIMER | — | |
| Appearance | Pasty liquid with fine aggregates comes in different colours | — |
| Density | 1.45 ± 0.05 | — |
| pH | 8 - 9 PRODUCT GRADES AND TEXTURES KingPlast ST75 comes with two different systems which is related to the final desired finish. | — |
| T type | is the normal textured uniform system; where the largest grain size appears uniformally on the whole finish. The T type comes with different large grain sizes which reflects in the final thickness. | — |
| S type | is the scratch type finish, where a selected large grain particles will be spreaded in the finish and gives a randomly scratch effect on the finish. The size of these large grains effect on the thickness of the applied layer. | — |
| The following table summarizes the system | KingPlast® ST75 Ready to use silicate based finish coat for external and | — |
| STRUCTURE MINIMUM | THEORETICAL | — |
| THICKNESS | CONSUMPTION (KG/ | — |
| (MM) | m²) | — |
| T1 | 1 1.8 | — |
| T1.5 | 1.5 2.5 | — |
| T2 | 2 3.4 | — |
| T3 | 3 5 | — |
| S1.5 | 1.5 2.6 | — |
| S2 | 2 3.5 | — |
| S3 | 3 4 MAINTENANCE To overcoat KingPlast ST75 use either KingPlast ST75 or KingPlast SN75 protective coatings as per | — |
Standards & Approvals
Usage & Packaging
KingPlast ST75 is available in 10 kg buckets and 25 kg pails. KingPlast Primer is available in 18 litre pails.
Shelf life is 1 year when stored under cover, out of direct sunlight and protected from extremes of temperature
Pail, Bucket
Product family
Ready to use acrylic based finish coat for external and internal applic…
Single component, high strength pre-mixed cementitious plaster
One component, high strength pre-mixed cementitious plaster
Single component, high strength pre-mixed cementitious plaster.