KingBond ETS100®
Flexible solvent free joints transition strip mortar.
SpecWorld has the Spec Pack, CSI specification and drawings for registered specifiers.
Overview
KingBond ETS100 is a three components coal tar epoxy based mortar supplied in pre-weighed quantities ready for on-site mixing and use. KingBond ETS100 is specially formulated from epoxy resin modified with coal tar and polysulphide polymer to produce a flexible and durable mortar with excellent adhesion to concrete, asphalt and steel surfaces.
Where to use
- Designed for use as a transition strip between expansion joints & bridge decks, asphalt, steel and concrete substrates.
- Industrial floor joint filler for concrete construction
- and control joints.
- KingBond ETS100-F is a fast curing winter grade version from KingBond ETS100.
Why use it
- Solvent free.
- Hard wearing with high abrasions resistance.
- Excellent adhesion to concrete, asphalt and steel surfaces.
- Withstand dynamic movement.
- Fast cure; KingBond ETS100-F.
- No priming is required.
- Excellent resistance to heat and oxidation.
- Maintains its mechanical properties under sunlight and weathering conditions.
Technical properties
| Elongation at break: (Neat resin) ASTM D638 | @ 25°C >40% @ 1 day >30% @ 7 days | @ 15°C >40% @ 1 day >30% @ 7 days |
|---|---|---|
| Water absorptionASTM D570 | < 0.5% | |
| VOCASTM D2369 | < 60 g/ltr | |
Ensure that the bottom and sides are thoroughly scraped; transfer the entire contents of the HARDENER container into the RESIN container. Using a mixer attached to a slow speed electric drill, mix for approximately 2 minutes until a uniform consistency is obtained. The resin mixture should then be transferred to a separate container or forced action mixer such as a creteangle type mixer, and the FILLER gradually added and mixed for a further 2 minutes or until the filler has thoroughly wetted out and a uniform consistency is obtained.
How to use
Surface preparation
The surface must be structurally sound, free from oil, grease and other forms of contamination. Concrete surface should be dry and suitably prepared either by scabbling or grit blasting to remove any surface laitance.
Mixing
KingBond ETS100 comprises of three components, a resin base, hardener and filler which are pre-weighed to the correct proportions. Under no circumstances should part mixing be carried out.
Application
KingBond ETS100 should be applied by first tamping, followed by trowelling using steel float.
WORKING TIME
KingBond ETS100 has a working time of approximately 30- 40 minutes at 25°C. Mixed material should not be left standing for any length of time prior to application, as this will considerably reduce its working time.
WORKING CONDITIONS
KingBond ETS100 should not be applied at temperatures below 5°C.
Curing
KingBond ETS100 should be allowed to cure for 14 hours at 25°C and 10 hours @ 35°C before being subjected to vehicle traffic. At 35°C, full mechanical and chemical properties are achieved after 3 days. However, KingBond ETS100-F needs 6 hours @ 25°C and 10 hours @ 15°C before being subjected to vehicle traffic.
| TECHNICAL PROPERTIES | ||
|---|---|---|
| KingBond ETS100 | KingBond ETS100-F | |
| Colour | black | Black |
| Working time | 30 - 40 min @ 25°C 15 - 25 min @ 35°C | 20 - 30 min @ 25°C 40 - 50 min @ 15°C |
| Shore A: ASTM D2240 | > 70 @ 1 day | > 80 @ 1 day |
| Shore D: ASTM D2240 | > 30 @ 1 day | > 40 @ 1 day |
| Solids | 100% | |
| Mixed density | 2.0 ± 0.1 g/cm³ | |
| Curing time: Initial cure/ vehicle traffic tack free time | 14 hr @ 25°C 10 hr @ 35°C | 6 hr @ 25°C 10 hr @ 15°C |
| Final cure/ chemical cure | 7 days @ 25°C 3 days @ 35°C | 5 days @ 25°C 7 days @ 15°C |
| Bond strength EN 1542 on Concrete Asphalt Steel | >2 MPa concrete failure >2 MPa Asphalt failure >1.5 MPa | |
| Recommended application temperature | 15 - 40°C | 8 - 30°C |
| Service temperature | -20 - 70°C | |
| Compressive strengthBS 6319, Part 2 | @ 25°C >8 MPa @ 1 day >20 MPa @ 7 days | @ 15°C >10 MPa @ 1 day >20 MPa @ 7 days |
| Tensile strength: (Neat resin)BS 6319, Part 7 & ASTM D638 | @ 25°C >3 MPa @ 1 day >8 MPa @ 7 days | @ 15°C >3 MPa @ 1 day >8 MPa @ 7 days |
| Flexural strengthBS 6319, Part 3 | @ 25°C >4 MPa @ 1 day >10 MPa @ 7 days | @ 15°C >3 MPa @ 1 day >10 MPa @ 7 days |
Cleaning
Clean uncured material with KINGKRETE solvent. Cured material can only be removed mechanically.
Coverage, packaging and storage
Yield
10 litre/20 kg Pack.
Packaging
KingBond ETS100 is available in 20 kg pack size comprising resin base, hardener and filler component.
Storage
Shelf life is 1 year when stored under cover, out of direct sunlight and protected from extremes of temperature. Failure to comply with the recommended storage conditions may result in premature deterioration of the product or packaging. For specific storage advice consult KingKrete's Technical Services Department.
Health and safety
As with all chemical products, care should be taken during use and storage to avoid contact with eyes, mouth, skin and foodstuffs. Treat splashes to eyes and skin immediately. If accidentally ingested, seek medical attention. Reseal containers after use. Use in well ventilated areas and avoid inhalation.