🌍 🌐 English
Adhesives, Mortars & Plasters

KingBond EPG10®

Solvent free general purpose epoxy adhesive.

SpecWorld has the Spec Pack, CSI specification and drawings for registered specifiers.

Compressive strength ASTM D695-96
≥ 75 MPa @ 7 days
Slant shear bond strength AASHTO T-237-73
> 30 MPa
Pot life
10 – 15 min
Mixed specific gravity
≈ 1.5 ± 0.05

Overview

KingBond EPG10 is a multi-purpose, two components, moisture tolerant, non-sag, solvent free epoxy resin adhesive.

Where to use

KingBond EPG10 is used for high strength fast set bonding adhesive for different material such as:

  • Concrete metals, and wood.
  • Timber joints and ceramics.
  • Fixing laminates/veneers.
  • Extruded polystyrene boards.
  • Closed cell Polyethylene boards.
  • PVC tiles.
  • Permanent installation of reinforcement starter bars and dowel bars.
  • Rubber.

Why use it

  • Fast set.
  • High bond strength.
  • Bonds to most common building materials.
  • Unaffected by water immersion.
  • Easy application. (1:1 mixing ratio).
  • High tensile and shear strength.

Technical properties

Values @ 25°C

Colour of mixed materialDark grey
Pot life10 – 15 min
Bond strengthASTM C882-99
(hard concrete to hard
concrete @ 15°C)
> 9 MPa @ 2 days
(moist cure)
> 11 MPa @ 14 days
(moist cure)
Bond strengthASTM C882-99
(fresh concrete over
hard concrete @ 25°C)
> 11 MPa @ 14 days
(moist cure)
Mixed specific gravity≈ 1.5 ± 0.05
Compressive strengthASTM D695-96≥ 75 MPa @ 7 days
Compressive modulusASTM D695-96≥ 1800 MPa @ 7 days
Slant shear bond strengthAASHTO T-237-73> 30 MPa
Water absorptionASTM D570-98≤ 0.1%
Heat deflectionASTM D648 @ 0.455 MPa≥ 50°C

Standards and approvals

KingBond EPG10 complies with AASHTO M237, Type II, slant shear bond strength and gel time and ASTM C881, Type I, II, IV, V, Grade 3, Class C.

How to use

Surface preparation
  • All Substrate should be sound and dust free.
  • Concrete surfaces should be dry and free of any laitance.
  • Metals, steel, copper, brass etc. surfaces should be degreased abraded.
  • Glass and ceramics should be degreased and abraded.
  • Rubber surface should be treated for 4 minutes with sulphuric or nitric acid or abraded.
  • Timber should be dry abraded.
Mixing

One part of component A should be mixed to one part of component B. To avoid waste only mix sufficient quantities that can be used within the pot life. Components should be scooped from the tins and mixed together thoroughly using a spatula or palette knife in a suitable tin or board, until a uniform grey paste is obtained.

Cleaning

All tools should be cleaned immediately before the adhesive reaches initial setting using KingBond solvent.

Limitations and notes

KingBond EPG10 setting time and pot life will vary depending on temperature and size of mix; extending at lower temperatures and smaller thicknesses of application.

Coverage, packaging and storage

Coverage

1.5 kg/m² @ 1 mm thick.

Packaging

KingBond EPG10 part A is available in 1, 5 kg packs and 5 gallon pails. KingBond EPG10 part B is available in 1, 5 kg packs and 5 gallon pails.

Storage

Shelf life is 1 year when stored under cover, out of direct sunlight and protected from extremes of temperature. Failure to comply with the recommended storage conditions may result in premature deterioration of the product or packaging. For specific storage advice consult KingKrete's Technical Services Department.

Health and safety

As with all chemical products, care should be taken during use and storage to avoid contact with eyes, mouth, skin and foodstuffs. Treat splashes to eyes and skin immediately. If accidentally ingested, seek medical attention. Reseal containers after use. Use in well ventilated areas and avoid inhalation.

Request the safety data sheet