KingFloor AS100®
Non slip flooring aggregates.
SpecWorld has the Spec Pack, CSI specification and drawings for registered specifiers.
Overview
Non-slip, chemically inert, graded, hard wearing aggregate available in four grades to suit most site requirements, they are identified as follows:
KingFloor AS100 No. 1 coarse
For use with KingFloor SL, KingFloor EP100 range and KingDeck systems or any other coating systems to produce a coarse textured, non-slip floor topping.
KingFloor AS100 No. 2 medium
For use with KingFloor EP100, KingFloor SL range and KingDeck systems or any other coating systems to produce a medium coarse textured floor finish.
Anti-slip Grain No.3 fine aggregate
For use with KingFloor EP100, KingFloor SL range and KingDeck systems or any other coating systems to produce a non-slip floor with a fine textured finish.
Anti-slip Grain No. 4 extra fine aggregate
For use only with KingFloor EP25 or KingFloor EP50 to provide a fine textured non-slip finish with thin floor coatings.
Where to use
KingFloor AS100 are designed for use with KingFloor resin products to produce non-slip industrial floors. Ideally suited for wet work areas in abattoirs, breweries, dairies, chemical industries, food processing areas, loading bays, ramps and walkways.
Why use it
- Range of products to suit most applications.
- Special grading to suit KingFloor range products.
- Pre-packed ready for immediate site use.
How to use
Method of use
APPLICATION INSTRUCTIONS
- All KingFloor AS100 should be clean and dry prior to application.
- KingFloor AS100No. 1, No. 2 and No. 3 are designed for use with KingFloor EP100, solvent free, resin based, roller applied floor coating, and KingFloor PU Seal, and KingFloor SL self-smoothing, solvent free epoxy floor toppings.
| Anti-slip grain | Finished floor | Finished floor thickness for KingFloor EP100 |
|---|---|---|
| No.1 | Coarse | 2.0-2.5 mm |
| No.2 | Medium | 1.0-2.0 mm |
| No.3 | Fine | 0.75-1.5 mm |
| No.4 | Extra fine | 0.3-0.6 mm |
- In the case of application onto the KingFloor SL products, a final coat of KingFloor EP100 is applied.
- KingFloor AS100 No. 4 is used in conjunction with KingFloor EP25 and KingFloor EP50 floor coatings.
Application
The specially graded aggregates are “scattered” onto the first rolled coat of KingFloor resin flooring whilst it is still wet. Sufficient KingFloor AS100 should be applied to completely cover or “blind” the surface.
The selected anti-slip grain should be allowed to fall vertically onto the resin coating rather than be thrown across the surface as this may cause bridges or scour the coatings, and damage the continuous film of the resin flooring.
When the first coat has dried, the excess aggregate can be brushed or vacuumed off the substrate and provided it is still clean and dry can be re-used.
The final roller coat of KingFloor EP50 can then be applied to produce a hard wearing, chemically resistant non-slip floor. The texture and thickness of the floor is determined by the choice of the anti-slip grain.
Coverage, packaging and storage
Packaging
KingFloor AS100 is available in 25 kg bags.
Storage
Shelf life is 1 year when stored under cover, out of direct sunlight and protected from extremes of temperature.
Failure to comply with the recommended storage conditions may result in premature deterioration of the product or packaging. For specific storage advice consult KingKrete's Technical Services Department.
Health and safety
As with all chemical products, care should be taken during use and storage to avoid contact with eyes, mouth, skin and foodstuffs. Treat splashes to eyes and skin immediately. If accidentally ingested, seek medical attention. Reseal containers after use. Use in well ventilated areas and avoid inhalation.