Renewables

Mass concreteLarge pours and foundations where heat and setting time must be controlled. 12 matches → Structural concreteFrames, slabs, columns and walls: workability, strength and durability. 14 matches → Ready-mix superplasticiser rangeThe KingMix polycarboxylate (PCE) range for ready-mix and site-batched concrete. Grades differ in water reduction, slump retention and early strength; your KingKrete engineer matches the grade to your cement, aggregates and placing time. 48 matches → Marine & chloride-exposed concreteConcrete in seawater, splash zones and chloride exposure. 7 matches → Cold-weather concretingAccelerating and antifreeze admixtures for concreting in low temperatures. 5 matches → Hot-weather concretingFor: summer pours in high temperatures: slump retention and controlled setting. 13 matches → Piles & diaphragm wallsFor: bored piles and diaphragm walls: long workability and cohesive tremie concrete. 4 matches →

Curing of slabs & decksCuring compounds that protect fresh concrete as it gains strength. Remove the curing film before any bonded screed, coating or tiling. 11 matches → Formwork releaseRelease agents for clean striking of cast-in-place formwork. 5 matches → Evaporation control in hot weatherFor: fresh slabs in sun and wind: stops plastic-shrinkage cracking before curing starts. 3 matches →

Structural crack injectionFor: dry, static cracks 0.2-10mm. 2 matches → Structural repair, horizontal or formedFor: high strength, large volume, free-flow. 3 matches → Rapid-turnaround repairFor: fast return to service or traffic. 3 matches → Structural strengthening (CFRP)Carbon-fibre plates and wraps to add capacity to beams, slabs and columns. 6 matches → Marine & splash-zone repairRepairs to piles, decks and quay walls in seawater. 28 matches →

Machine base plate groutingFor: standard duty, ambient temperature; heavy dynamic or vibration load. 6 matches → High-temperature equipment baseFor: exposure up to 400°C. 1 match → Structural anchoringFor: cracked or uncracked concrete, seismic-rated. 2 matches → Pile top fairing and void fillingFor: high-flow pourable grout. 3 matches → Turbine & tower foundationsHigh-strength grouting of turbine and tower base connections. 20 matches → General-duty anchoringFor: handrails, dowels, non-structural fixings. 4 matches → Steel column base & holding-down boltsFor: steel column base plates and holding-down bolts. 4 matches →

Exterior movement jointsFor: weather-exposed, high movement. 10 matches → Structural floor jointsFor: heavy traffic, chemical exposure, limited movement. 5 matches →

Steel structures & tank exteriorsPolyurethane and epoxy protection for steel and tank shells. 20 matches → Chemical-resistant liningsLinings for bunds, process areas and chemical containment. 16 matches → Fuel & hydrocarbon containmentLinings resistant to fuels, oils and hydrocarbons. 23 matches → Marine & splash-zone coatingsProtection for concrete in seawater and spray. 27 matches →

Control RoomsFloor systems for control rooms. 2 matches → Turbine HallsFloor systems for turbine halls. 3 matches → Plant rooms & workshopsHard-wearing, oil-resistant floors for plant and workshops. 22 matches →

Basements & FoundationsWaterproofing for: without hydrostatic pressure; with hydrostatic pressure; negative-side only. 20 matches → RoofsWaterproofing for: non-exposed roof; exposed flat roof; exposed Sloped roof; roof garden / landscaped roof; sloped metal roof (profiled / standing seam). 34 matches → Plant RoomsWaterproofing for: wet service areas; critical equipment areas. 6 matches → Joints (Construction & Movement)Waterproofing for: construction joints; expansion / movement joints. 23 matches → Retaining WallsWaterproofing for: positive-side accessible; negative-side only. 19 matches →