🌍 🌐 English
Tile & Stone Adhesives and Grouts

KingTile EN5®

Tile adhesive liquid additive and performance enhancer.

SpecWorld has the Spec Pack, CSI specification and drawings for registered specifiers.

Specific gravity
Around 1.0
Active solid content
48 - 50 %

Overview

KingTile EN5 is a single component polymeric liquid that is designed to improve physical and bonding properties of cementitious tile adhesives.

Where to use

KingTile EN5 is ideally designed for use in the following applications:

  • Bonding of thin polymer modified screeds and/or toppings to old substrates.
  • As an additive to KingTile range of tile adhesive where enhanced bonding to various substrates is required.
  • To enhance KingFloor screeds performance.
  • As a primer for absorbent surfaces.
  • For bonding large tile sizes (above 30 x 30 cm), stone materials and slabs.
  • Ceramic tiles on asphalt screeds.
  • Swimming pools and wet areas.
  • To produce waterproof renders.

Why use it

  • Effectively increases the bonding/ adhesion of cementitious adhesives.
  • Excellent water proof additives which help produce water-proof renders, screed and toppings.
  • Effective plasticizer, giving improved workability and cohesion.
  • Improved mechanical and physical properties by increasing tensile, flexural and adhesive strengths.
  • Reduces shrinkage and cracking and screeding mixes.
  • Good freeze/thaw resistance.
  • Chloride free.

Technical properties

Values @ 25°C

Active solid content48 - 50 %
Specific gravityAround 1.0
ColourWhite
Slant shear strength
Type 1 (dry cure)
Type II (after immersion)
KingTile EN5ASTM C1059 requiremants
>9.0MPa2.8 MPa
>16.0MPa8.6 MPa

Standards and approvals

KingTile EN5 complies with ASTM C1059-99, Type 1 & 2, when tested in accordance with test method C1042.

How to use

Substrate preparation

The Substrate should be sound, clean and free from contamination. Surface Laitance should be removed by mechanical means.

Gypsum substrates and anhydrite screeds must be primed with Probond GP prior to appllication of products mixed with KingTile EN5.

Mixing

Bonding agent:

The recommended mix to produce slurry consistency can be achieved by mixing, 1 KingTile EN5 : 1 clean water : 3 OPC cement by volume. Use a stiff brush to apply a thick coat to damp surfaces. Application of the subsequent renders, mortar, or screed should take place while the bond coat is still wet (tacky). DO NOT apply on dry bond coats. If bond coat dries, roughen the dry coat before applying a further coat.

With KingFix C10 and KingTile C100:

Dilute KingTile EN5 with mixing water by 1:1 ratio.

With KingTile C50:

Dilute KingTile EN5 with mixing water by 1:3 ratio.

With KingFloor C100T and C200T:

Dilute KingTile EN5 with mixing water by 1:2 ratio.

When high deformability is required completely substitute water with KingTile EN5.

Note: Products mixed with KingTile EN5 will have a notably reduced open time in hot climates.

Application

Apply the mix on the substrate with a medium sized notched trowel. Choose the trowel that provides a contact area between the tile adhesive and at least 65 - 70% to the back of the tiles subject to ligh foot traffic and 100% contact for outdoor areas and heavy traffic situations.

Best adhesion will be obtained by applying a thin coat of the mix onto the substrate using a flat side trowel then applying the desired thickness of the mix using the appropriate trowel in relation to type and size of tyles.

For example:

Type of TileNotch Size
Mosaics or 5 x 5 cm tiles3 - 4 mm
Up to 12 x 12 tiles5 mm
Up to 20 x 20 tiles6 mm
Over 20 x 20according to tile back

Grout works using the KingFill and KingFix ranges can start 4 - 8 hours for wall and 24 - 36 hours for floors.

Cleaning

All tools should be cleaned immediately after use with fresh clean water. Hardened materials should be cleaned mechanically.

Coverage, packaging and storage

Packaging

KingTile EN5 is available in 5, 25 and 200 litres drums.

Storage

Shelf life is 1 year when stored under cover, out of direct sunlight and protected from extremes of temperature.

Failure to comply with the recommended storage conditions may result in premature deterioration of the product or packaging. For specific storage advice consult KingKrete's Technical Services Department.

Health and safety

As with all chemical products, care should be taken during use and storage to avoid contact with eyes, mouth, skin and foodstuffs. Treat splashes to eyes and skin immediately. If accidentally ingested, seek medical attention. Reseal containers after use. Use in well ventilated areas and avoid inhalation.

Request the safety data sheet