KingFill C125®
Water repellent cementitious grout for ceramic tiles
SpecWorld has the Spec Pack, CSI specification and drawings for registered specifiers.
Overview
KingFill C125 Interior and exterior tile grout, suitable for grouting all types of ceramic tiles on floors and walls when water repellent grout is required.
Where to use
- For grouting of all types of ceramic tiles.
- Suitable for bathrooms and kitchens and wet areas. Non-sag, can be used for wall applications.
- Can be used internally and externally. High polymer content.
Why use it
- Does not absorb splashed water or liquids.
- Extended open - wet time.
- Hygienic and mould resistant.
- Water resistant, will not be affected in wet areas.
- Ready for use, just requires the addition of water.
- High bond strength.
- Suitable for internal and external applications.
- Available in a wide range of colors.
Technical properties
Values @ 23 ± 2°C. W/P = 0.34
| Compressive strength EN12808-3 | 4 MPa @ 1 day @ room temperature) ≥ 15 MPa @ 28 days @ room temperature |
|---|---|
| Working time | ≈ 90 mins. @ 20°C ≈ 30 mins. @ 35°C |
| Minimum application temperature | 5°C |
| Fresh wet density | 1.75 gm/ cm³ |
| Resistance to abrasion EN12808-2 | 491 mm³ |
| Shrinkage | 0.025 mm/ m |
| Water absorption after 240 mm EN12808-5 | 1.7 gm |
Standards and approvals
KingFill C125 complies with BS5980 and BS EN13888: 2002.
How to use
Substrate preparation
All surfaces must be clean and free from oil, grease or loose materials. Gap to be filled should not exceed 6mm to avoid slumping.
Mixing
To ensure proper mixing, a mechanically powered mixer or drill fitted with suitable paddle should be used.
To ensure proper mixing, a mechanically powered mixer or drill fitted with suitable paddle should be used.
1.6 liters of clean water should be added to clean container for each 5 kg. The powder is then added slowly to the water while mixing continuously with low speed mixer/ drill (400 - 600 rpm). Mixing time should be continued for 3 minutes until uniform consistency is obtained. Allow to stand for 3 minutes, and then mix again for 1 minute before using.
Application
- Apply using a spatula or a scraper.
- Remove excess material from the face of the tile using a dry cloth.
- Finish by running the tip of the gloved finger over the surface or by using a suitably curved tool.
- After drying, clean tiles with a damp sponge.
- It is recommended to remove grout from the tile surfaces before full setting of the grout. Failure to do so may result in difficulty in removing any remains.
Cleaning
All tools should be cleaned immediately after use with fresh clean water. Hardened materials should be cleaned mechanically.
Limitations and notes
- Low temperatures (between 5°C) will a°ect the physical properties of the unset material.
- During application and for at least 12 hours from application, the product should not be exposed to any water.
Coverage, packaging and storage
Yield
The approximate yield of grout can be calculated as per the following equation:
Yield (m²/kg) = 5.7
WD (0.02 + 1/L+1/H)
Where;
L: Tile length (cm)
H: Tile width (cm)
D: Average joint depth (mm)
W: Average joint width (mm)
Note: Grout yield subject to ±15% tolerance.
Packaging
KingFill C125 is available in 5 kg bags.
Storage
Shelf life is 1 year when stored under cover, out of direct sunlight and protected from extremes of temperature.
Failure to comply with the recommended storage conditions may result in premature deterioration of the product or packaging. For specific storage advice consult KingKrete's Technical Services Department.
Health and safety
As with all chemical products, care should be taken during use and storage to avoid contact with eyes, mouth, skin and foodstuffs. Treat splashes to eyes and skin immediately. If accidentally ingested, seek medical attention. Reseal containers after use. Use in well ventilated areas and avoid inhalation.