🌍 🌐 English
Adhesives, Mortars & Plasters

KingBlock MC150®

Block and brick laying cementitious mortar with water resistance.

SpecWorld has the Spec Pack, CSI specification and drawings for registered specifiers.

Flexural strength ASTM C348
≥ 2.5 MPa @ 28 days
Tensile strength ASTM C307
≥ 2 MPa @ 28 days
Pot life
1 - 2 hr
Fresh wet density (mixed)
2.15 ± 0.05 g/cm³

Overview

KingBlock MC150 is a polymer modified, ready to use interior and exterior block adhesive specially designed for use with blocks and bricks.

KingBlock MC150 is composed of a blend of cement, sand, limestone, dry powder additives and selected polymers which when mixed with water produces a thixotropic mortar suitable for fixing all types of blocks and bricks, and to be used on the block walls for filling gaps.

Where to use

  • For permanent fixing of all types of blocks and bricks.
  • Can be used internally and externally.
  • Non sag, can be used for vertical and horizontal surfaces.

Why use it

  • Water resistant, will not be affected in wet areas.
  • Ready for use, just requires the addition of water.
  • Non sag, good consistency.
  • High bond strength.
  • Suitable for internal and external application.
  • Shrinkage controlled, polymer modified cementitious mortar.
  • Complies with the LEED requirements for VOC and formaldehyde limits.

Technical properties

Values @ 25°C. W/P = 0.10

ColourGrey
Fresh wet density (mixed)2.15 ± 0.05 g/cm³
Pot life1 - 2 hr
Compressive strengthASTM C109/109M-02> 40 MPa @ 7 days
> 45 MPa @ 28 days
Flexural strengthASTM C348≥ 2.5 MPa @ 28 days
Tensile strengthASTM C307≥ 2 MPa @ 28 days
Maximum aggregate size3.0 mm
Setting time: ASTM C191
Initial6 - 7 hr
Final8 - 9 hr
Temperature limitationsBelow 5°C and above 38°C

2.5 - 3.0 litres (for each 25 kg bags) of clean water should be added to clean container. The powder is then added slowly to the water while mixing continuously with low speed mixer/drill (400 - 600 rpm). Mixing time should be continued for 3 minutes until a uniform consistency is obtained.

Standards and approvals

KingBlock MC150 complies with the requirements of:

  • ASTM C387 as Mortar for Unit Masonry, Type M, S and N.
  • ASTM C270 Type M, S, N and O.

How to use

Blocks condition

All used blocks must be checked to be clean and free from oil or any loose materials. It is recommended to wet the used blocks before the application of the adhesive, especially in hot and dry conditions.

Mixing

To ensure proper mixing, a mechanically powered mixer or drill fitted with suitable paddle should be used.

Application
  • Spread to a uniform thickness of 15 - 25 mm using a trowel.
  • Place blocks firmly over the applied area.
  • Do not apply large areas of adhesives that cannot be covered within the open wet time of the adhesive.
Curing

The applied areas should be protected from direct sunlight and heavy wind. Curing with water is needed for at least 2 - 3 days after setting.

Cleaning

All tools should be cleaned immediately after use with fresh clean water.

Coverage, packaging and storage

Yield

Approximately 12.75 litres/25 kg bag.

Packaging

KingBlock MC150 is available in 25 and 50 kg bags.

Storage

Shelf life is 1 year when stored under cover, out of direct sunlight and protected from extremes of temperature.

Failure to comply with the recommended storage conditions may result in premature deterioration of the product or packaging. For specific storage advice consult KingKrete's Technical Services Department.

Health and safety

As with all chemical products, care should be taken during use and storage to avoid contact with eyes, mouth, skin and foodstuffs. Treat splashes to eyes and skin immediately. If accidentally ingested, seek medical attention. Reseal containers after use. Use in well ventilated areas and avoid inhalation.

Request the safety data sheet