KingFill C50®
Highly flexible cementitious tile grout for wide joints applications high water repellency effect.
SpecWorld has the Spec Pack, CSI specification and drawings for registered specifiers.
- Working time
- 70 - 90 min
- Fresh wet density
- 1.60 ± 0.10 g/cm3
Overview
KingFill C50 is a highly flexible, premixed blend of cement, lime, well graded aggregate and special additives that when mixed with water produces a distinguished tile grout typically designed for wide joint widths range from 3 to 15 mm.
The unique composition of KingFill C50 makes it ideally used to fill the wide joints and provide a smooth and attractive finishing free of any notable cracks. It is also characterized by a very low water absorption rate and thus it represents an excellent solution for grouting in exterior and submerged areas.
KingFill C50 is available in wide range of brilliant colours that provide a uniform and aesthetic joint appearance.
Where to use
- Grouting all types of ceramic tiles and natural stone for joints between 3 to 15 mm.
- Excellent for bathrooms, kitchens and other wet areas.
- Excellent for submerged areas.
- Suitable for commercial and residential buildings.
- Non-sag, excellent for wall applications.
- Excellent for internal and external applications.
Why use it
- Specially designed for wide grouting.
- High abrasion resistance.
- Reduced water absorption properties, suitable for wet areas.
- Low shrinkage rate, free of cracks.
- Uniform colour, for aesthetic joint appearance.
- Easy to apply, non-sag with good workability.
- Available in wide range of brilliant colours.
Technical properties
Values @ 23 ± 2 C. w/p = 0.19
| Fresh wet density | 1.60 ± 0.10 g/cm3 |
|---|---|
| Working time | 70 - 90 min |
| Compressive strengthISO 13007-4,4.1.4ISO 13007-4,4.1.5 | ≥ 15 MPa (standard conditions) ≥ 15 MPa (after freeze-thaw cycles) |
| Flexural strengthISO 13007-4,4.1.3ISO 13007-4,4.1.5 | ≥ 2.5 MPa (standard conditions) ≥ 2.5 MPa (after freeze-thaw cycles) |
| Shrinkage ISO13007-4,4.3 | ≤ 2.0 mm/m |
| Water absorptionISO 13007-4,4.2 | ≤ 0.2 g @ 240 min |
| VOCASTM D2369 | < 10 g/ltr (complies with LEED) |
Standards and approvals
KingFill C50 complies with the following standards:
- ISO 13007-3 and BS EN 13888 as an improved cementitious grout with additional characteristics of reduced water absorption and high abrasion resistance (CG2AW).
How to use
Substrate preparation
Before grouting, ensure that the adhesive has completely dried and hardened. Adhesive should be left for 24 hours before applying the grout, unless rapid setting adhesive is used.
All tiles and joints must be clean and free from oil, grease or loose materials.
Remove the tile spacers and ensure that the grout joints are uniform and their widths do not exceed 15 mm to avoid slumping.
Mixing
To ensure proper mixing, a mechanically powered mixer or drill fitted with suitable paddle should be used.
0.9 - 1.0 litres of clean fresh water for each 5 kg bag (water/powder ratio of 0.18 - 0.2 by weight) should be added to a clean container. The powder is then added slowly to the water while mixing continuously at low speed (400 - 600 rpm).
Mixing time should be continued for 3 minutes until a uniform consistency and free of lumps mixture is obtained.
Allow a slake time for 5 minutes, then remix for additional 1 minute without adding any more water.
Important: Adding too much water will weaken the joints, cause surface discoloration and promote the formation of cracks. Always follow the mentioned mixing ratio.
Application
- Using appropriate spatula or rubber float, fill with pressure the joints completely with KingFill C50.
- Immediately remove the excess grout by moving the spatula or the edge of the rubber float diagonally to the tiles.
- When the grout starts to set (usually 30 - 40 minutes at normal conditions), use a damped sponge in a circular motion to remove the excess grout and level the joints.
- After drying, clean the tiles surface using a dry cloth.
It is recommended to remove grout from the tile surfaces before full setting of the grout. Failure to do so may result in difficulty in removing any remains and makes it necessary to use a mechanical means in cleaning, which may scratch the tile surfaces.
Cleaning
All tools should be cleaned immediately after use with fresh clean water. Hardened materials should be cleaned mechanically.
Limitations and notes
Do not use for:
- Joint widths exceeding 15 mm.
- Grouting tiles in industrial floors where high chemical resistance is required.
- Cases where a rapid utilization of surfaces is required.
- Filling expansion, contraction or construction joints in walls and floors. These joints should be filled with a suitable flexible sealant from the KINGKRETE range.
Coverage, packaging and storage
Yield
The approximate yield of grout can be calculated as per the following equation:
Yield (m²/kg) = 6
WD (0.02 + 1/L+1/H)
Where;
L: Tile length (cm)
H: Tile width (cm)
D: Average joint depth (mm)
W: Average joint width (mm)
Note: Grout yield subject to ±15% tolerance.
Packaging
KingFill C50 is available in 5 kg bags.
Storage
Shelf life is 1 year when stored under cover, out of direct sunlight and protected from extremes of temperature.
Failure to comply with the recommended storage conditions may result in premature deterioration of the product or packaging. For specific storage advice consult KingKrete's Technical Services Department.
Health and safety
As with all chemical products, care should be taken during use and storage to avoid contact with eyes, mouth, skin and foodstuffs. Treat splashes to eyes and skin immediately. If accidentally ingested, seek medical attention. Reseal containers after use. Use in well ventilated areas and avoid inhalation.