KingCoat SR®
High quality general purpose water repellent impregnation based on solvent borne Silane/Siloxane.
SpecWorld has the Spec Pack, CSI specification and drawings for registered specifiers.
Overview
KingCoat SR is a ready for use, high quality single component solvent based silane/siloxane water repellent impregnation for application on vertical or steeply sloping concrete, mineral-based natural and artificial stone, cementitious substrates, mineral plasters and mineral paints.
Where to use
KingCoat SR provides excellent water repellency and protection from weathering to vertical or steeply sloping concrete, mineral-based natural and artificial stone, cementitious substrates, and mineral paints.
KingCoat SR acts as a moisture barrier and can be used for injection into walls to prevent rising damp.
Why use it
Deep penetration into substrate.
Excellent reduction of water and chloride intrusion.
Excellent resistance to alkalis and UV light.
Absorbed by the substrate, does not form film and hence does not change or stain the substrate.
Increases considerably freeze thaw resistance.
Minimizes efflorescence.
Breathable, allows for water vapour release.
Excellent resistance to dust and dirt pick-up.
Technical properties
Values @ 25°C
| Specific gravity | 0.81 ± 0.02 |
|---|---|
| Viscosity (Brookfield, N₁S₂₀) | < 5 cP |
| Rapid chloride permeabilityASTM C1202 | Very low |
| ISATBS 1881, Part 208:1996 (replacesBS 1881, Part 5:1970) | < 0.005 ml/m²/sec, after 10 min |
| Reduction in water absorptionASTM C642 | ≥ 85% |
| VOCASTM D2369 | < 700 g/ltr |
How to use
Surface preparation
Surface must be clean, sound and free from oil, grease, curing compound, or any contamination. Any contaminants should be removed by light grit blasting. Water jet is then used as the end step of substrate cleaning.
Note: Avoid the use of acidic or alkaline chemical detergents and cationic surfactants. If detergents are used for cleaning, it is necessary to rinse well the cleaned surface by water in order to remove any detergent residue.
Application
It is recommended to apply two consecutive coats of KingCoat SR at the stated rate of application, or one flood coat. Impregnation can be carried out using airless spray machine, brush, or roller.
Curing
The water repellent properties fully develop in approximately 72 hours @ 25°C.
Cleaning
Tools and equipment can be cleaned with KINGKRETE-solvent when wet. Hardened materials must be cleaned mechanically.
Limitations and notes
- Before applying KingCoat SR be sure to cover non- absorbent surfaces properly (windows, aluminum frames, etc.). KingCoat SR cures fast and will be extremely difficult, to remove after a few hours.
- KingCoat SR should not be applied when rain is forecasted within 24 hours. Wait at least 24 hours after rain or water cleaning.
- Be sure that impregnated surfaces by KingCoat SR are not exposed to water and rain for at least 5 hours after application.
- DO NOT USE DETERGENTS for cleaning impregnated surfaces by KingCoat SR, washing occurs only by water.
Coverage, packaging and storage
Coverage
0.1 - 0.4 litre/m² depends on the porosity of the substrate.
Packaging
KingCoat SR is available in 20 litre pails and 200 litre drums.
Storage
Shelf life is 1 year when stored under cover, out of direct sunlight and protected from extremes of temperature. Failure to comply with the recommended storage conditions may result in premature deterioration of the product or packaging. For specific storage advice consult KingKrete's Technical Services Department.
Health and safety
As with all chemical products, care should be taken during use and storage to avoid contact with eyes, mouth, skin and foodstuffs. Treat splashes to eyes and skin immediately. If accidentally ingested, seek medical attention. Reseal containers after use. Use in well ventilated areas and avoid inhalation.